Set Up An Appointment

 

 

Right here in the next paragraph yow will discover a good deal of amazing resources in relation to Installing A Bathtub.

Setting up a bath tub isn't exactly brain surgery, however it does call for solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is conveniently accessible, the project can move rapidly; if you need to open up a wall surface to get rid of the old tub and position the brand-new bath tub, the job is much harder. In either case, the project is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as set in the brand-new one. Make certain you have actually certified on your own for the work and are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you mount a brand-new bath tub in your shower room if you have actually already purchased a new bathtub as well as don't need to change the arrangement of your previous water supply pipes.
Your devices and also product list must make up the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Preparing for the Installation

To start with, the sustaining framework provided with the bath should be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to see to it that if the tap features a plastic washer, it is fitted between the bath and also the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets device to stop stress on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its final placement.

 

 

Removing Old Taps

If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome as a result of the restricted gain access to that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will originate from the pipelines. When the supply pipelines have been gotten rid of, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Prior to going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.

 

 

Installing the Bathtub

Utilizing both wood boards under its feet, place the tub in the called for placement. The wooden boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the level and also adjusting the feet on the bathtub until the spirit level checks out degree.
To set up faucets, fit all-time low of the outermost flexible tap port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Activate the water supply as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if required. Fill up the tub as well as additionally examine the overflow electrical outlet and the typical electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the maker's instruction manual. Tiling and sealing around the bathtub ought to wait up until the tub has been used at least once as this will settle it into its final placement.

 

 

Fitting New Touches

If the tails of the new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in location between the tap and also the sink. Safeguard the faucet in position with the producer provided backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap ports. The former kind must be linked to the faucet finishes initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bath tub

In the location where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to fracture a stiff seal, causing the water to penetrate the wall surface in between the bath and also the tiling, causing problems with wetness as well as possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your components and installations. They are offered in tubes and also cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to allow for the motion experienced when the tub is in usage. The sealant can fracture fairly early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is suggested to fit the tiles utilizing waterproof or waterproof sticky and also grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I am very inquisitive about A Step-by-Step Guide to Installing a Bathtub and I really hope you appreciated my entry. Loved our post? Please share it. Let another person discover it. Thanks so much for your time invested reading it.

Set An Appointment